Pump
From Wikipedia, the free encyclopedia
 |
It has been suggested that Pump testing be merged into this article or section. (Discuss) |
A pump is a device used to move fluids, such as gases, liquids or slurries. A pump displaces a volume by physical or mechanical action. One common misconception about pumps is the thought that they create pressure. Pumps alone do not create pressure; they only displace fluid, causing a flow. Adding resistance to flow causes pressure. Pumps fall into two major groups: positive displacement pumps and rotodynamic pumps. Their names describe the method for moving a fluid.
Contents |
[edit] Positive displacement pumps
A positive displacement pump causes a fluid to move by trapping a fixed amount of it then forcing (displacing) that trapped volume into the discharge pipe. A positive displacement pump can be further classified according to the mechanism used to move the fluid:
- Rotary-type, for example, the lobe, external gear, internal gear, screw, shuttle block, flexible vane or sliding vane, helical twisted roots (e.g. the Wendelkolben pump) or liquid ring vacuum pumps.
- Reciprocating-type, for example, piston or diaphragm pumps.
[edit] Rotary-type pumps
[edit] Gear pump
This uses two meshed gears rotating in a closely fitted casing. Fluid is pumped around the outer periphery by being trapped in the tooth spaces. It does not travel back on the meshed part, since the teeth mesh closely in the centre. Widely used on car engine oil pumps.
[edit] Progressing cavity pump
Widely used for pumping difficult materials such as sewage sludges, contaminated with large particles, this pumps consists of a helical shaped rotor, about 10 times as long as its width. This can be visualised as a central core of diameter x, with typical a curved spiral wound around of thickness half x, although of course in reality it is made from one casting. This shaft fits inside a heavy duty rubber sleeve, of wall thickness typically x also. As the shaft rotates, fluid is gradually forced up the rubber sleeve. Such pumps can develop very high pressure at quite low volumes.
[edit] Roots-type pumps
The low pulsation rate and gentle performance of this Roots-type positive displacement pump is achieved due to a combination of its two 90° helical twisted rotors, and a triangular shaped sealing line configuration, both at the point of suction and at the point of discharge. This design produces a continuous and non-vorticuless flow with equal volume. High capacity industrial "air compressors" have been designed to employ this principle as well as most "superchargers" used on internal combustion engines.
[edit] Peristaltic pump
A peristaltic pump is a type of positive displacement pump used for pumping a variety of fluids. The fluid is contained within a flexible tube fitted inside a circular pump casing (though linear peristaltic pumps have been made). A rotor with a number of "rollers", "shoes" or "wipers" attached to the external circumference compresses the flexible tube. As the rotor turns, the part of tube under compression closes (or "occludes") thus forcing the fluid to be pumped to move through the tube. Additionally, as the tube opens to its natural state after the passing of the cam ("restitution") fluid flow is induced to the pump. This process is called peristalsis and used in many biological systems such as the gastrointestinal tract.
[edit] Reciprocating-type pumps
Reciprocating pumps are those which cause the fluid to move using one or more oscilating pistons, plungers or membranes (diaphragms).
Reciprocating-type pumps require a system of suction and discharge valves to ensure that the fluid moves in a positive direction. Pumps in this category range from having "simplex" one cylinder, to in some cases "quad" four cylinders or more. Most reciprocating-type pumps are "duplex" (two) or "triplex" (three) cylinder. Furthermore, they can be either "single acting" independent suction and discharge strokes or "double acting" suction and discharge in both directions. The pumps can be powered by air, steam or through a belt drive from an engine or motor. This type of pump was used extensively in the early days of steam propulsion (19th century) as boiler feed water pumps. Though still used today, reciprocating pumps are typically used for pumping highly viscous fluids including concrete and heavy oils and special applications demanding low flow rates against high resistance.
[edit] Compressed-air-powered double-diaphragm pumps
One modern application of positive displacement diaphragm pumps are compressed-air-powered double-diaphragm pumps. Run on compressed air these pumps are intrinsically safe by design, although all manufacturers offer ATEX certified models to comply with industry regulation. Commonly seen in all areas of industry from shipping to process, SandPiper, Wilden Pumps or ARO are generally the larger of the brands. They are relatively inexpensive and can be used for almost any duty from pumping water out of bunds, to pumping hydrochloric acid from secure storage (dependant on how the pump is manufactured - elastomers / body construction). Suction is normally limited to roughly 6m although heads can be almost unlimited.
[edit] Rotodynamic pumps
Rotodynamic pumps (or dynamic pumps) are those in which kinetic energy is added to the fluid by increasing the flow velocity. This increase in energy is converted to a gain in potential energy (pressure) when the velocity is reduced prior to or as the flow exits the pump into the discharge pipe. This conversion of kinetic energy to pressure can be explained by the First law of thermodynamics or more specifically by Bernoulli's principle. Dynamic pumps can be further subdivided according to the means in which the velocity gain is achieved.
These types of pumps have a number of characteristics:
- Continuous energy
- Conversion of added energy to increase in kinetic energy (increase in velocity)
- Conversion of increased velocity (kinetic energy) to an increase in pressure head
One practical difference between dynamic and positive displacement pumps is their ability to operate under closed valve conditions. Positive displacement pumps physically displace the fluid; hence closing a valve downstream of a positive displacement pump will result in a continual build up in pressure resulting in mechanical failure of either pipeline or pump. Dynamic pumps differ in that they can be safely operated under closed valve conditions (for short periods of time).
[edit] Centrifugal pump
A centrifugal pump is a rotodynamic pump that uses a rotating impeller to increase the pressure and flowrate of a fluid. Centrifugal pumps are the most common type of pump used to move liquids through a piping system. The fluid enters the pump impeller along or near to the rotating axis and is accelerated by the impeller, flowing radially outward or axially into a diffuser or volute chamber, from where it exits into the downstream piping system. Centrifugal pumps are typically used for large discharge through smaller heads.
Centrifugal pumps are most often associated with the radial flow type. However, the term "centrifugal pump" can be used to describe all impeller type rotodynamic pumps[1] including the radial, axial and mixed flow variations.
[edit] Radial flow pumps
Often simply referred to as centrifugal pumps. The fluid enters along the axial plane, is accelerated by the impeller and exits at right angles to the shaft (axially). Radial flow pumps operate at higher pressures and lower flow rates than axial and mixed flow pumps.
[edit] Axial flow pumps
Axial flow pumps differ from radial flow in that the fluid enters and exits along the same direction parallel to the rotating shaft. The fluid is not accelerated but instead "lifted" by the action of the impeller. They may be likened to a propeller spinning in a length of tube. Axial flow pumps operate at much lower pressures and higher flow rates than radial flow pumps.
[edit] Mixed flow pumps
Mixed flow pumps, as the name suggests, function as a compromise between radial and axial flow pumps, the fluid experiences both radial acceleration and lift and exits the impeller somewhere between 0-90 degrees from the axial direction. As a consequence mixed flow pumps operate at higher pressures than axial flow pumps while delivering higher discharges than radial flow pumps. The exit angle of the flow dictates the pressure head-discharge characteristic in relation to radial and mixed flow.
[edit] Eductor-jet pump
This uses a jet, often of steam, to create a low pressure. This low pressure sucks in fluid and propels it into a higher pressure region.
[edit] Hydraulic ram pumps
A hydraulic ram is a water pump powered by hydropower. It functions as a hydraulic transformer that takes in water at one "hydraulic head" (pressure) and flow-rate, and outputs water at a higher hydraulic-head and lower flow-rate. The device utilizes the water hammer effect to develop pressure that allows a portion of the input water that powers the pump to be lifted to a point higher than where the water originally started. The hydraulic ram is sometimes used in remote areas, where there is both a source of low-head hydropower, and a need for pumping water to a destination higher in elevation than the source. In this situation, the ram is often useful, since it requires no outside source of power other than the kinetic energy of water.
[edit] Application
Pumps are used throughout society for a variety of purposes. Early applications includes the use of the windmill or watermill to pump water. Today, the pump is used for irrigation, water supply, gasoline supply, air conditioning systems, refrigeration (usually called a compressor), chemical movement, sewage movement, flood control, marine services, etc.
Because of the wide variety of applications, pumps have a plethora of shapes and sizes: from very large to very small, from handling gas to handling liquid, from high pressure to low pressure, and from high volume to low volume.
Liquid and slurry pumps can lose prime and this will require you to prime the pump by adding liquid to the pump and inlet pipes to get the pump started. Loss of "prime" is usually due to ingestion of air into the pump. The clearances and displacement ratios in pumps used for liquids and other more viscus fluids cannot displace the air due to its lower density.
[edit] Specifications
Pumps are commonly rated by horsepower, flow rate, outlet pressure in feet (or metres) of head, inlet suction in suction feet (or metres) of head. The head can be simplified as the number of feet or metres the pump can raise or lower a column of water at atmospheric pressure.
From an initial design point of view, engineers often use a quantity termed the specific speed to identify the most suitable pump type for a particular combination of flow rate and head.
[edit] Pumps as public water supplies
One sort of pump once common worldwide was a hand-powered water pump over a water well where people could work it to extract water, before most houses had individual water supplies.
From this came the expression "parish pump" for "the sort of matter chattered about by people when they meet when they go to get water", "matter of only local interest". However water from pitcher pumps are more prone to contamination since it is drawn directly from the soil and does not undergo filtration, this might cause gastrointestinal related diseases.
Today, hand operated village pumps are considered the most sustainable low cost option for safe water supply in resource poor settings, often in rural areas in developing countries. A hand pump opens access to deeper groundwater that is often not polluted and also improves the safety of a well by protecting the water source from contaminated buckets. Pumps like the Afridev pump are designed to be cheap to build and install, and easy to maintain with simple parts. However, scarcity of spare parts for these type of pumps in some regions of Africa has diminished their utility for these areas.[citation needed]
[edit] Pumping power
The power added to the fluid flow by the pump (Po), is defined using SI units by:
where:
- PO is the output power of the pump (W)
- ρ is the fluid density (kg/m3)
- g is the gravitational constant (9.81 m/s2)
- H is the energy Head added to the flow (m)
- Q is the flow rate (m3/s)
Power is more commonly expressed as kW (103 W) or horsepower (divide kW by 0.746), H is eqivalent to the pressure head added by the pump when the suction and discharge pipes are of the same diameter. The power required to drive the pump is determined by dividing the output power by the pump efficiency
Power needed to pump a given flow against a given head and pipe size, can be calculated using this spread sheet.[3]
Various aspects of pumping energy usage are covered in "Energy Efficiency in Pumping".[4] Energy is consumed by the pump, and also lost in the pipework and these must be considered.
[edit] Pump efficiency
Pump efficiency is defined as the ratio of the power imparted on the fluid by the pump in relation to the power supplied to drive the pump. Its value is not fixed for a given pump, efficiency is a function of the discharge and therefore also operating head. For centrifugal pumps, the efficiency tends to increase with flow rate up to a point midway through the operating range (peak efficiency) and then declines as flow rates rise further. Pump performance data such as this is usually supplied by the manufacturer before pump selection. Pump efficiencies tend to decline over time due to wear (e.g. increasing tolerances and impellers reducing in size).
One important part of system design involves matching the pipeline headloss-flow characteristic with the appropriate pump or pumps which will operate at or close to the point of maximum efficiency.
Pump efficiency is an important aspect and pumps should be regularly tested. Thermodynamic pump testing is one method.
[edit] Gallery
 19th century Dutch diesel pump in Rijswijk, Netherlands |
 Three cylinder air diver's pump "П3" (Pump three), manufactured in Soviet Union in 1977 |
 Domestic Central Heating Pump |
 A two-lobe pump (multiple rotor, positive displacement type) |
 A pump powered by a tractor's PTO |
[edit] See also
- Affinity laws
- Balancing machine
- Beam pump and walking beam pump
- Bicycle pump
- Breast pump
- Concrete pump
- Cyclic pump
- Gas compressors
- Gerotor
- Hand pump
- Hydraulic ram pump
- Jockey pump
- Metering pump
- Pumping station
- Pump testing
- Pumpjack (oil pump)
- Scroll pump, most used in scroll compressors
- Tesla turbine
- Thermodynamic pump testing
- Wind pump
[edit] References
- ^ Karassik, Igor J.; Messina, Joseph P.; Cooper, Paul; Heald, Charles C. (2001). Pump Handbook (3rd ed.). New York: McGraw-Hill. ISBN 9781591243618.
- ^ Hill, Donald Routledge (1996). A History of Engineering in Classical and Medieval Times. London: Routledge. p. 143. ISBN 0415152917. http://books.google.com/books?id=MqSXc5sGZJUC&pg=PA143&dq=Taccola+first+piston&as_brr=3&hl=en.
- ^ Pumping Power calculator
- ^ Energy Efficiency in Pumping
[edit] Further reading
- Australian Pump Manufacturers' Association. Australian Pump Technical Handbook, 3rd edition. Canberra: Australian Pump Manufacturers' Association, 1987. ISBN 0731670434.
- Robbins, L. B. "Homemade Water Pressure Systems". Popular Science, February 1919, pages 83–84. Article about how a homeowner can easily build a pressurized home water system that does not use electricity.
[edit] External links
 |
Wikimedia Commons has media related to: Pumps |
- Europump—the Association Européenne des Constructeurs de Pompes, a European trade group
- calicut universiry—engineering collage
- www.lightmypump.com—Pump and pump system information
- www.pumpschool.com—Pump education devoted primarily to rotary positive displacement pumps
- Fluid Handling Resource Center
- Parish Pumps of Eastern Essex in the UK
